+ =======================================
+ ---
+ Version 1
+   Supplied by Realtime CNC. Adding new post processor.
+
+ =======================================


POST_NAME = "Redline Laser No Z V1 (mm) (*.ngc)"

FILE_EXTENSION = "ngc"

UNITS = "MM"

LASER_SUPPORT = "YES"

+------------------------------------------------
+    Line terminating characters
+------------------------------------------------

LINE_ENDING = "[13][10]"

+------------------------------------------------
+    Block numbering
+------------------------------------------------

LINE_NUMBER_START     = 0
LINE_NUMBER_INCREMENT = 1
LINE_NUMBER_MAXIMUM = 9999999

+================================================
+
+    Formatting for variables
+
+================================================

VAR LINE_NUMBER = [N|A|N|1.0]
VAR POWER = [P|C|S|1.0|10.0]
VAR SPINDLE_SPEED = [S|A| S|1.0]
VAR FEED_RATE = [F|C|F|1.1]
VAR X_POSITION = [X|C|X|1.4]
VAR Y_POSITION = [Y|C|Y|1.4]
VAR Z_POSITION = [Z|C|Z|1.4]
VAR ARC_CENTRE_I_INC_POSITION = [I|A|I|1.4]
VAR ARC_CENTRE_J_INC_POSITION = [J|A|J|1.4]
VAR X_HOME_POSITION = [XH|A|X|1.4]
VAR Y_HOME_POSITION = [YH|A|Y|1.4]
VAR Z_HOME_POSITION = [ZH|A|Z|1.4]
VAR SAFE_Z_HEIGHT = [SAFEZ|A|Z|1.4]

+================================================
+
+    Block definitions for toolpath output
+
+================================================

+---------------------------------------------------
+  Unique revision number for this post-processor
+---------------------------------------------------

begin REVISION_COMMENT

"%"
"(VECTRIC POST REVISION)"
"([REVISION])"
"([POST_NAME])"


+---------------------------------------------------
+  Commands output at the start of the file
+---------------------------------------------------

begin HEADER

"( [TP_FILENAME] )"
"( File created: [DATE] - [TIME])"
"( Redline J Tech Laser)"
"G00 G17 G40 G21 G54"
+"G0[ZH]"
"G0[XH][YH]"
"G90"
"M4"


+---------------------------------------------------
+  Command output after the header to switch spindle on
+---------------------------------------------------

begin SPINDLE_ON

"M4[S]"

+---------------------------------------------------
+  Commands output for rapid moves
+---------------------------------------------------

begin RAPID_MOVE

"G1[X][Y][P]"


+---------------------------------------------------
+  Commands output for the first feed rate move
+---------------------------------------------------

begin FIRST_FEED_MOVE

"G1[X][Y][F][P]"


+---------------------------------------------------
+  Commands output for feed rate moves
+---------------------------------------------------

begin FEED_MOVE

"G1[X][Y][P]"


+---------------------------------------------------
+  Commands output for the first clockwise arc move
+---------------------------------------------------

begin FIRST_CW_ARC_MOVE

"G2[X][Y][I][J][F][P]"

+---------------------------------------------------
+  Commands output for a new segment - toolpath
+  with same toolnumber but maybe different feedrates
+---------------------------------------------------

begin NEW_SEGMENT

+"[N] [S] M4"
"([TOOLPATH_NAME])"
"([TOOLPATH_NOTES])"

+---------------------------------------------------
+  Commands output for clockwise arc  move
+---------------------------------------------------

begin CW_ARC_MOVE

"G2[X][Y][I][J][P]"


+---------------------------------------------------
+  Commands output for the first counterclockwise arc move
+---------------------------------------------------

begin FIRST_CCW_ARC_MOVE

"G3[X][Y][I][J][F][P]"


+---------------------------------------------------
+  Commands output for counterclockwise arc  move
+---------------------------------------------------

begin CCW_ARC_MOVE

"G3[X][Y][I][J][P]"

+---------------------------------------------------
+  Commands output when the jet is turned on
+---------------------------------------------------

begin JET_TOOL_ON




+---------------------------------------------------
+  Commands output when the jet is turned off
+---------------------------------------------------

begin JET_TOOL_OFF




+---------------------------------------------------
+  Commands output when the jet power is changed
+---------------------------------------------------

begin JET_TOOL_POWER



+---------------------------------------------------
+  Commands output at the end of the file
+---------------------------------------------------

begin FOOTER

"M5"
+"G0[ZH]"
"G0[XH][YH]"
"M2"
"%"