{"id":2520,"date":"2015-04-24T11:14:30","date_gmt":"2015-04-24T16:14:30","guid":{"rendered":"https:\/\/jtechphotonics.com\/?page_id=2520"},"modified":"2024-11-26T17:20:45","modified_gmt":"2024-11-26T23:20:45","slug":"cnc-shark-upgrade","status":"publish","type":"page","link":"https:\/\/jtechphotonics.com\/?page_id=2520","title":{"rendered":"CNC Shark Laser Upgrades for Sale"},"content":{"rendered":"\n

We have gotten a lot of requests for upgrading the CNC shark by Next Wave.  It is a nice woodworking tool that can do a lot of projects in your woodworking shop.  Now how about adding a laser?  Of course you can!   It is not very hard if you have the newest version of the control box. We now have a Laser kit that is fully integrated with the Shark controller that allows it to seamlessly work with Vectric and Next Wave Automation software.<\/p>\n\n\n\n

Laser Upgrade for HD4 and HD5 machines<\/h2>\n\n\n\n

We are going to go over how to install the J Tech laser on the Shark HD4 and HD5 machines with the newest controller box.<\/p>\n\n\n\n

Laser and Fan Extension Cable Installation<\/h3>\n\n\n\n

Insert the laser spindle shaft into a 1\/4″ collet on the spindle or router and tighten snuggly.<\/p>\n\n\n

\n
\"\"<\/a>
Insert the laser into the chuck<\/figcaption><\/figure>\n<\/div>\n\n\n

Run the cord around from behind the spindle\/router ensuring that it is clear of any Z axis movement. A Velcro strap was used here to hold it in place. Anything can be used to temporarily hold the cord if it will stay secured.<\/p>\n\n\n

\n
\"\"<\/a>
Velcro strap<\/figcaption><\/figure>\n<\/div>\n\n\n

Continue running the cord up the spindle\/ router to join with the power cord and cooling water lines if present.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Keep running the cord over the top and temporarily secure to the other lines.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Complete running the cord by bringing up to the beginning of the chain<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Open the cable chain behind the gantry and insert the laser and fan power cords.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

After running the cords in the cablechain close all the clips.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Now connect the extension cables to the laser and fan cables.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Continue running the cables down the gantry leg to the front of the base cable chain.
As with the cable chain on the gantry, open the clips and lay the cords inside being sure to avoid any kinking or pinching of the cords. Afterwards be sure to close all the clips.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

This will leave just over 18\u201d at the end of the cable chain at the front of the base using a 10\u2019 cable extension. Cable lengths of up to 25\u2019 are available.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Laser and Driver Installation<\/h3>\n\n\n\n

The Shark HD interface kit includes a breakout board, ribbon cable, and input cable for the laser driver. They are shown here:<\/p>\n\n\n

\n
\"\"<\/a>
Interface kit contents<\/figcaption><\/figure>\n<\/div>\n\n\n

Using a small flat screwdriver loosen the screws on binding lugs #15 and #16. On the breakout board. Connect the control signal cable to the breakout board as follows;<\/p>\n\n\n\n


Insert the RED wire into #15<\/strong>
Insert the BLACK wire into #16<\/strong><\/p>\n\n\n\n


Tighten the screws snuggly.<\/p>\n\n\n

\n
\"\"<\/a>
Black in 16 and Red in 15<\/figcaption><\/figure>\n<\/div>\n\n\n

Both ends of the 20-conductor ribbon cable are identical and can be used end for end, but they are keyed and can only be inserted one way.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Plug the ribbon cable into the breakout board by opening the locking arms and lining up the key on the cable and the slot on the board as denoted by the red arrows in the picture.<\/p>\n\n\n

\n
\"\"<\/a>
Line up the ribbon cable<\/figcaption><\/figure>\n<\/div>\n\n\n

Press down evenly and firmly while inserting the cable. As the cable is inserted the locking arms will close onto the connector locking it in place.<\/p>\n\n\n

\n
\"\"<\/a>
Press down to lock the connector<\/figcaption><\/figure>\n<\/div>\n\n\n

Locate the 20-conductor connector on the front of the CNC controller. You will see the slot is on the top of the connector as denoted by the red arrow.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Position the breakout board on top of the controller. This will help line up the cable as it meant wrap back onto itself so the board and laser drive can mount on top of the controller.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Insert the ribbon cable into the controller with the key facing up as shown in the picture making sure it is firmly seated all the way in.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

It should look like this when completed.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Connect all of the cables to the back of the laser driver to complete the installation.<\/p>\n\n\n

\n
\"\"<\/a><\/figure>\n<\/div>\n\n
\n
\"\"<\/a><\/figure>\n<\/div>\n\n\n

Software<\/h2>\n\n\n\n

We recommend using the vectric laser module for your CAD software. Use the Shark post processor included in the laser module when doing your laser files. Output the toolpath file like you normally do for carving and run it on your shark controller. Note, it will not do photo engraving unless you use the “Ready to Raster” program from NextWave. We have not had any good results when using this, so I wouldn’t count on doing photos. You could alternatively use the “laser end mill” post processor found here<\/a>.<\/p>\n\n\n\n

If you don’t have the Shark laser post processor, then you can find it here as well.<\/p>\n\n\n\n

\n
Vectric Laser Module Post Processors<\/a><\/blockquote>